check out the new remote control Jockey Wheel SmartBar Canegrowers rearview170 Cobb Grill Skid Row Recovery Gear Caravan Industry Association of Australia
Members Login
Username 
 
Password 
    Remember Me  
Click here for the Grey Nomads website -> The Grey Nomads Forum -> Techies' Corner -> Chinese diesel heater manual and info
Post Info TOPIC: Chinese diesel heater manual and info
Mike Harding


Guru

Status: Offline
Posts: 4706
Date:
Chinese diesel heater manual and info
Permalink  

A thread was recently necro-ed asking for info on diesel heaters; necro threads are an issue on the forum because of its default setting for viewing threads hence I've started a new thread.

The first attachment is the full manual for the generic Chinese diesel heaters I found somewhere on the net the second is the FAQ from the extensive Facebook group, the following notes are from my own experiments:

----

Bleeding:

Hold the "OK" and "Down" buttons

When "Off" flashes press the "Up" button

----

Ryco Z675 fuel filter works well

----

(Don't mess here unless you know what you're doing)

Config menu - Settings button 3 times until padlock icon

PIN = 1688 press OK after each digit

----

To toggle between temperature and pulse rate:

Press OK twice

Press Settings and Up together

----

 

I suggest you do not run these heaters on thermostatic temperature control their design is not suited to it. Instead use the pump pulse rate to manually control temperature, in my large caravan in Victoria I find the minimum setting of 1.6Hz works 95% of the time and when the van become too hot I crack a window at each and and opposite sides to balance things out.

It is a good idea to run the heater at maximum for 20 minutes once every few months.

 

Edit:

This is the original thread which contains a useful table from "Are We Lost".



-- Edited by Mike Harding on Saturday 24th of September 2022 01:22:09 PM

Attachments
Facebook1 FAQ.doc (548.5 kb)
__________________

 

"I beseech you in the bowels of Christ think it possible you may be mistaken"

Oliver Cromwell, 3rd August 1650 - in a letter to the General Assembly of the Kirk of Scotland
Yellow van


Member

Status: Offline
Posts: 5
Date:
Permalink  

Thank you. Great info and advice. I wasn't sure at time of asking if it's best to find old threads on a subject or start new one. Learning.....

__________________
Radar


Guru

Status: Offline
Posts: 5447
Date:
Permalink  

Hi Mike 

Great information, have now stored this for future reference. 

Thank you.



__________________
Yellow van


Member

Status: Offline
Posts: 5
Date:
RE: Chinese diesel heater noisy exhaust
Permalink  

Has anyone got any tips re a product or way to wrap diesel heater exhaust to deaden the booming noise please?

__________________
Ian G


Senior Member

Status: Offline
Posts: 101
Date:
RE: Chinese diesel heater manual and info
Permalink  

I don't notice the exhaust but I would like to know how to deaden the ticking noise from the pump.  Ian



__________________
Plain Truth


Guru

Status: Offline
Posts: 1481
Date:
Permalink  

Ian G wrote:

I don't notice the exhaust but I would like to know how to deaden the ticking noise from the pump.  Ian

 I used an engine mount to fix the pump to the chassis,even better if you can keep it of the chassis as it tends to amplify any sound.

Mount.JPGmount 1.jpg

 



Attachments
__________________
Are We Lost


Guru

Status: Offline
Posts: 1054
Date:
Permalink  

Booming noise? Mine is a bit noisy on startup but then settles down at normal speed. I would hardly call it booming, but certainly audible. I bought a second muffler for mine and can just push it onto the end. That makes a fair bit of difference. I am not sure if the extra back pressure affects the heater, so rarely use it. Just ensure your exhaust pipe is not transmitting noise through direct contact anywhere onto the chassis.

For the pump ticking noise, stopping the pump body from touching anything makes a big difference. I have mine wrapped in insulation and held against a piece of foam with cable ties, rather than use the supplied mount. The fuel feed line from the pump to the heater also generates noise. Just letting the tubing touch a panel transmits noise. So I bought some soft rubber moulding with a hole in the centre and fed the tubing into that. Some fuel lines vary. The thin translucent variety benefit most from that strategy.



-- Edited by Are We Lost on Wednesday 5th of October 2022 11:02:15 AM

__________________
KJB


Guru

Status: Offline
Posts: 828
Date:
Permalink  

Plain Truth wrote:
Ian G wrote:

I don't notice the exhaust but I would like to know how to deaden the ticking noise from the pump.  Ian

 I used an engine mount to fix the pump to the chassis,even better if you can keep it of the chassis as it tends to amplify any sound.

Mount.JPGmount 1.jpg

 

 

Also disconnect and turn the Pump around then extend both inlet and outlet fuel lines so they have a 180 Degree bend to travel around  then pulsing movement of the pump does not travel back along the fuel lines.....the bends absorb the movement and the sound. (I have also  used this method when installing similar fuel pumps in cars ......has a good effect)  The less "fixings" that the fuel lines have to the body  the  quieter it will be.......KB



__________________

KB
Mike Harding


Guru

Status: Offline
Posts: 4706
Date:
Permalink  

Yellow van wrote:

Has anyone got any tips re a product or way to wrap diesel heater exhaust to deaden the booming noise please?

They should not make a booming noise indeed the exhaust of mine makes hardly any noise at all.

I met a bloke, somewhere, about two years ago and he was complaining of the same issue, it transpired his heater did not have a silence fitted simply an open end exhaust pipe. They should have a silence similar to this:

E-bay silencer



__________________

 

"I beseech you in the bowels of Christ think it possible you may be mistaken"

Oliver Cromwell, 3rd August 1650 - in a letter to the General Assembly of the Kirk of Scotland
Ian G


Senior Member

Status: Offline
Posts: 101
Date:
Permalink  

Plain Truth wrote:
Ian G wrote:

I don't notice the exhaust but I would like to know how to deaden the ticking noise from the pump.  Ian

 I used an engine mount to fix the pump to the chassis,even better if you can keep it of the chassis as it tends to amplify any sound.

Mount.JPGmount 1.jpg

 

 Looks like you have also changed the original clamp to a rubber lined hose clamp, looks good to me, I'll give that a try,. thanks Ian



__________________
Yellow van


Member

Status: Offline
Posts: 5
Date:
Permalink  

Thanks everyone, all useful comments. My exhaust is attached to the chassis so that must be my error. I'll shift it and wrap it in fibreglass stuff (obvs heatproof and not over the outlet). My pump is mounted similarly, under the van. Tick tick tick. A job for when it's not raining. Learning.....

__________________
Ian G


Senior Member

Status: Offline
Posts: 101
Date:
Permalink  

Yellow van wrote:

Thanks everyone, all useful comments. My exhaust is attached to the chassis so that must be my error. I'll shift it and wrap it in fibreglass stuff (obvs heatproof and not over the outlet). My pump is mounted similarly, under the van. Tick tick tick. A job for when it's not raining. Learning.....

 I don't think having it attached to your chassis would make it any louder as most would have it that way, the exhaust is a little noisy on start up but after 10 mins it should be quiet, as Mike says do you have a silencer attached to the end ?  Ian



__________________
msg


Guru

Status: Offline
Posts: 1663
Date:
Permalink  

www.youtube.com/watch

This guy talks about how he fixed the ticking noise

__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Click here for the Grey Nomads website -> The Grey Nomads Forum -> Techies' Corner -> Chinese diesel heater manual and info
Tweet this page Post to Digg Post to Del.icio.us
Purchase Grey Nomad bumper stickers Read our daily column, the Nomad News The Grey Nomad's Guidebook