check out the new remote control Jockey Wheel SmartBar rearview170 Beam Communications SatPhone Shop Topargee products Enginesaver Low Water Alarms
Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Waeco Powersupply


Guru

Status: Offline
Posts: 1467
Date:
Waeco Powersupply


Waeco Ps2.JPGWaeco Ps4.JPGWaeco Ps5.JPGWaeco Ps6.JPGWaeco Ps10.JPGWaeco Ps14.JPGOn another Forum i noticed a person was charged $460 to get his Waeco fridge repaired as it wouldnt run on 240V. It had been running on aYamaha digital sinewave generator, this should not have been a problem. this got me thinking as i have a 3yr old CF-40 Waeco, what could go wrong with these powersupplys? I removed mine from the fridge & checked it out. First thing i noticed is a very small relay to automaticly change from 240V to 12V, its actually switching 24V from Powersupply to 12VDC, its ratings are240VAC 7Amp, to use it in a low voltage situation you can atleast halve its rating. This Relay is a potential cause of problems & dry solder joints on the board. If the 240V side of the power supply has been subject to over voltage there is a fuse soldered to the board worth checking. Next part that may fail in this situation is the 240V bridge rectifier ($5). Q1 is a IRFPC50 mosfet may also be damaged ($15) this is the most expensive part in the powersupply. There is also one capacitor that may fail C4 100Uf 35V. On the 24VDC side of the powersupply is 2 Caps that may cause problems eventualy if they dry out C16/19 2200Uf 35V. This powersuply is out of a 3Yr old CF-40 Waeco.



__________________
D.L.Bishop


Guru

Status: Offline
Posts: 1467
Date:

Waeco Ps2.JPGWaeco Ps bypass.JPGTo bypass the 240v powersupply if nolonger working Remove Red+ wire from the DC socket & White + wire from the circuit board which comes from the powersupply. Run a thick red wire from the DC socket+ to the Circuit board + where the White wire was. The fridge should run on 12V now.



__________________
D.L.Bishop


Senior Member

Status: Offline
Posts: 460
Date:

Yes also saw that and wondered why some one would spend that amount getting it fixed when a new board would be much less than that..
Have a box full of bits just like that, they just need going over .....
Not many people will pull the back off their fridge and solder bits to it and change wires....
Have let the smoke out of a few at times..big smile..
Have a good easter ......
Bob

__________________

Land Rover Discovery Chipped TD5 Manual ,Air Springs, Anti Sway. T.C.
Auto level. Van, Roadstar 21.6 Voyager 4000 all sola powered.



Guru

Status: Offline
Posts: 1467
Date:

Hi Bob, Unfortunatly this isn the first time people have been charged that mutch to just replace the powersupply board. I suspect that it wouldnt cost mutch to repair the board.



__________________
D.L.Bishop


Senior Member

Status: Offline
Posts: 460
Date:

Very true, I have a lot of bits if you were looking for anything ,, Just give me a pm ....

__________________

Land Rover Discovery Chipped TD5 Manual ,Air Springs, Anti Sway. T.C.
Auto level. Van, Roadstar 21.6 Voyager 4000 all sola powered.



Guru

Status: Offline
Posts: 1467
Date:

Another potential fault in the powersupply is failure to start up. This can be caused by R2 100K 2Watt metal film resistor(10c part) It can go high in value or open circuit. Its used to kick start the SMPS at turn on.



__________________
D.L.Bishop


Guru

Status: Offline
Posts: 1467
Date:

WAECO CD-40AC VERA SMPS.JPGHere is the circuit as an aid for anyone who is capable of repairing one. I should point out that the 24V DC side is isolated from the 240V AC side.



-- Edited by DeBe on Saturday 30th of April 2011 12:31:05 PM

__________________
D.L.Bishop


Guru

Status: Offline
Posts: 1467
Date:

DANFOSS comp.1.JPGTo test a compressor & its module, remove wires from C & T  then bridge them with a jumper. The compressor should run, this test was done on 12V if using the in built powersupply it will be 24V. The 2 top thick wires are also the best place to check for run voltage.



__________________
D.L.Bishop


Guru

Status: Offline
Posts: 4161
Date:

Thanks for the useful info, DeBe. Much appreciated.


__________________

"No friend ever served me, and no enemy ever wronged me, whom I have not repaid in full."

Lucius Cornelius Sulla - died 78 BC 

 



Guru

Status: Offline
Posts: 6882
Date:

The first sign of trouble when my Waeco 240V circuit board died wa a blown fuse. I replaced the fuse but it went again.
So I'm running it on a transformer 240v-12v at the moment with a new circuit standing by to be installed.


__________________

20ft Roma caravan - Mercedes Benz Sprinter - SA-based at the moment.
Transport has no borders.

Management makes the decisions, but is not affected by the decisions it makes.



Newbie

Status: Offline
Posts: 1
Date:

Blew up my fridge on 240V a little while ago. My fault, using a mate's crappy $2 gennie, that will learn me!
Anyway, can anyone identify the capacitor that was in the red circle? All of it's mates are 472M and I'm assuming it's the same, however, it does appear to be a little smaller in size in other images.
IMG_0515.jpg


__________________


Guru

Status: Offline
Posts: 1467
Date:

Hi Rippah, The part is V1 & its a MOV, 7D431K. The replacement is avalable from Jaycar RN-3406 for $1.75. Its a surge protector which in an over voltage situation can be destroyed & blow the mains fuse on the board.



__________________
D.L.Bishop


Guru

Status: Offline
Posts: 1467
Date:

Hi, You should be able to remove it without shifting the compressor. The only parts i moved was bend one bracket as shown, & moved the reciever drier (cylinderical copper object with a capilliary tube coming from it.) The polly fuse is a light brown square thin object by the relay.



-- Edited by DeBe on Thursday 28th of June 2012 07:36:36 PM

__________________
D.L.Bishop


Newbie

Status: Offline
Posts: 3
Date:

I have a CF-50 which has the signs of a dodgy polyfuse and Waeco have confirmed from my serial number that it is one of those affected. Out of warranty of course and in any case there is no service agent where I live. I am/was an electronics engineer so I should have no problem fixing the PSU, particularly after DeBe kindly posted the circuit diagram. However, I know nothing about refrigeration and am a bit concerned about moving the compressor to a point where I can remove the PSU. There is obviously the possibility of damaging the possibly work hardened copper pipes that go up into the fridge. One of the photos above shows at least one of the rear mounting brackets bent back, presumably so the compressor can pulled out sideways rather than dropped down. Is this the way to proceed? Any help with pulling the thing apart would be appreciated.

__________________


Guru

Status: Offline
Posts: 1467
Date:

WAECO P-S PTC.JPGHeres a pict of the Polly fuse.



__________________
D.L.Bishop


Newbie

Status: Offline
Posts: 3
Date:

many thanks DeBe. I'll look at it in the morning.

__________________


Newbie

Status: Offline
Posts: 3
Date:

Hi DeBe.

I found the easiest way of getting the PSU out was a combination of your method and lowering the compressor about an inch. I replaced the polyfuse and the fridge works OK on 240VAC so I didn't break anything! I'll try it in the car tomorrow.

Many thanks for your help with this.

__________________


Member

Status: Offline
Posts: 13
Date:
Waeco Cooler Circuit Board?


We have a Waeco brand electric cooler model CF-40. It came with our 2007 Winnebago Vectra when we bought it about a year ago. I've had it on in the past, but this is our first extended road trip and now it doesn't work.
We're getting power both on the 120 volt & 12 volt circuits. The fuses both on the outside & inside of the box are good. We've got power to the power supply box and from the 26 volt power from the power supply box to the circuit board. Nonetheless, still no display on the control panel. No power light and no error light.
I assume the board is bad. I can't find a schematic for the board (no manf. name only a number of 005224 REV:C). I can't even find a place to buy the board.
We're hoping someone has had some experience with this problem or where to get help.

Thanks in advance for any help!

Chris & Marily
Winter Haven, Florida, USA


Attachments
__________________

Chris & Mairly

Where Ever HaRV Takes Us



Guru

Status: Offline
Posts: 1467
Date:
RE: Waeco Powersupply


WAECO CD-40 AC VERA.JPGWAECO CD-40 AC VERA 2.JPGWAECO CD-40 AC VERA 8.JPGHi Chris & Marily. Can you post a sharper picture of the other side of the circuit board? Possable places for trouble are dry solder joints around the Relay or the 2 Regulator ICs 7810 & 7805 at the top of your picture. The regulator 7810 should have 12 or 24V on one leg center leg goes to ground & the other should have 10V DC on it.  With 7805 it should have 12/24Vdc on one leg, center leg ground, other leg should have 5V DC on it. Will put picture of a CF-40 board same as yours except it doesnt have the  relay fitted as its on the Mains to 24V powersuply board.



__________________
D.L.Bishop


Guru

Status: Offline
Posts: 1476
Date:

I have a problem with my Waeco on 240 volt as it made a sizzling sound when I turned the240 volt on and it blew the circuit breaker in the van and on the site power pole.
I have not looked at it yet but it still works on 12 volt when there is power in the dual battery
Ken

__________________
DUN WURKUN
Dan


Member

Status: Offline
Posts: 8
Date:

Hi everyone,

I have been inspired to pull my waeco cf 50 out of the never to be seen again black hole in my shed as I think it has a blown polyfuse and would like to replace it. From what I have read I think need to replace it with a larger capacity one. Can anyone tell me what polyfuse I should use?

Cheers,

Dan

__________________


Guru

Status: Offline
Posts: 1467
Date:

Hi Dan, i would try one from Altronics, PTC fuse R4562A for $1.50 they have a trip current of 7.5Amp.



__________________
D.L.Bishop


Member

Status: Offline
Posts: 10
Date:

Hi i know its an old post, but was wondering if anyone can tell me either from experience or the circuit diagram what Uc3844 does. I have a blown one (wet foam had fallen on the MOSFET after replacing a thermistor) and there are 2 available on a search of the ic number on element14 that are nearly identical, the only difference one outputs 5v, the other 13.4 v. Can someone tell me which one is right? ( I've ordered both as they are only $2.60 each!) thanks in advance!

__________________


Guru

Status: Offline
Posts: 1467
Date:

The UC3844 is a Switch Mode Power Supply driver IC. I would be using the original IC number. There is 3 other UC 38xx types which are different. The Mosfet may also be damaged.

__________________
D.L.Bishop


Member

Status: Offline
Posts: 10
Date:

As mine is blown and the number is no longer viewable I searched using your picture but the number comes up with a couple of possibilities with different following letters ( not on the ic in the picture) the difference being the output voltage, any idea which one I should be using? I have also bought the MOSFET so will replace at the same time.

__________________


Guru

Status: Offline
Posts: 1467
Date:

The UC3842 is a Switch Mode Power Supply driver IC. I would be using the original IC number. There is 3 other UC 38xx types which are different. The Mosfet may also be damaged. Here is the Data on the UC3842A controller chip, the Ic you are getting should match this, as far as I know there is only one UC3842A IC.UC3842A.1.jpgUC3842A.2.jpgUC3842A.3.jpg



Attachments
__________________
D.L.Bishop


Member

Status: Offline
Posts: 10
Date:

I have ordered this one..

au.element14.com/jsp/search/productdetail.jsp

Pretty sure it's right!

__________________


Member

Status: Offline
Posts: 10
Date:

Also ordered this one but now think it is wrong, as it is a B not an A!

au.element14.com/jsp/search/productdetail.jsp

__________________


Guru

Status: Offline
Posts: 1467
Date:

bairsjw wrote:

Also ordered this one but now think it is wrong, as it is a B not an A!

au.element14.com/jsp/search/productdetail.jsp


This one should be fine as its specs are the same as the A, probably just a later version of the original. 



__________________
D.L.Bishop


Guru

Status: Offline
Posts: 4161
Date:

ISTM that R18, R19, and R20 in the circuit diagram are setting the output voltage to approximately 28V, not 24V.

Vout = Vref x (R18 + R19 + R20) / (R19 + R20) = 2.5 x (26.5 + 2.4 + 0.22) / (2.4 + 0.22) = 27.8V



__________________

"No friend ever served me, and no enemy ever wronged me, whom I have not repaid in full."

Lucius Cornelius Sulla - died 78 BC 

 

1 2 3 4  >  Last»  | Page of 4  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
Purchase Grey Nomad bumper stickers Read our daily column, the Nomad News The Grey Nomad's Guidebook