check out the new remote control Jockey Wheel SmartBar rearview170 Beam Communications SatPhone Shop Topargee products Enginesaver Low Water Alarms
Members Login
Username 
 
Password 
    Remember Me  
Click here for the Grey Nomads website -> The Grey Nomads Forum -> Techies' Corner -> Old 10amp and 15amp power outlets
Post Info TOPIC: Old 10amp and 15amp power outlets
Micko69


Member

Status: Offline
Posts: 22
Date:
Old 10amp and 15amp power outlets
Permalink  

Hi everyon,

there is a thread on this however it was last used in 2009. I thought I would start a new one. Am having some real problems replacing old 10 and 15 amp with new ones. The new ones dont fit between the out and inner wall. I have bought the largest spacers (20 mm) and they still dont make the outlets fit. The outlets that I bought said they replace the old version but they dont. This is really giving me the shiites, can anyone please point me in the right direction. 
thx

Mick



Attachments
__________________
TimTim


Guru

Status: Offline
Posts: 555
Date:
Permalink  

Try using a backing plate Or mounting flang as they are called.

https://www.caravansplus.com.au/clipsal-power-inletoutlet-backing-plate-white-p-1009.html?srsltid=AfmBOoqor2bGOEBhlSHHy-WbPtBhV_HcqZSL-deqa2pojMdxcLnqOKuG

Or you can see a different type of in the attached photos.



-- Edited by TimTim on Friday 11th of October 2024 10:40:38 AM

__________________
Micko69


Member

Status: Offline
Posts: 22
Date:
Permalink  

Thanks for replyin,

I have these spacers or flanges as they are also called. My outlets old sit flush inside the wall cavity and has room for the wiring to be connected. 



-- Edited by Micko69 on Friday 11th of October 2024 10:59:20 AM

__________________
Corndoggy


Senior Member

Status: Offline
Posts: 399
Date:
Permalink  

Try getting an electrician to replace them as if your not one, it is illegal. But then you obviously don't care about that. This is the only answer that should be given to this question.



-- Edited by Corndoggy on Friday 11th of October 2024 01:15:09 PM

__________________
Ben Taxyl


Member

Status: Offline
Posts: 15
Date:
Permalink  

Perhaps Mick is qualified.



__________________
Possum3


Guru

Status: Offline
Posts: 8735
Date:
Permalink  

You can purchase a mounting block to allow enough space for cabling. www.ebay.com.au/itm/192974840239

__________________

Possum; AKA:- Ali El-Aziz Mohamed Gundawiathan

Sent from my imperial66 typewriter using carrier pigeon, message sticks and smoke signals.
Dick0


Guru

Status: Offline
Posts: 1325
Date:
Permalink  

Hi Mick,

This is a surface mount 15A inlet for caravans that will solve your problem.

 

15A Caravan Inlet Outlet RV Camper Motor Home Power Socket Weatherproof 240V | eBay

 

Socket.jpg



Attachments
__________________

Cheers, Richard (Dick0)

"Home is where the Den is parked, Designer Orchid Special towed by Jeep Grand Cherokee Limited"

"4x250W solar panels, Epever 80A charger and 3x135Ah Voltax Prismatic LiFePO4 Batteries".
Corndoggy


Senior Member

Status: Offline
Posts: 399
Date:
Permalink  

Ben Taxyl wrote:

Perhaps Mick is qualified.

 Qualified and has to ask a question like that. He isn't qualified and if he is he needs to find a completely new job cause I wouldn't  have him change the batteries in my TV remote if he is qualified.


-- Edited by Corndoggy on Saturday 12th of October 2024 10:15:10 AM



-- Edited by Corndoggy on Saturday 12th of October 2024 10:35:27 AM

__________________
Peter_n_Margaret


Senior Member

Status: Offline
Posts: 313
Date:
Permalink  

Ahhh. The electrical police are at large. hmm
No reason why he does not buy the bits he needs (so he gets exactly what he wants) and have them installed by someone else.

But that is none of your business.

Cheers,

Peter



__________________

OKA196 DIY, self contained 4WD MH, 1160W PV, 326Ah of CALB LiFePO4 batteries, 1.3kW inv, 310L water, 350-450L diesel.
Bicyclecamper


Guru

Status: Offline
Posts: 1418
Date:
Permalink  

Agree PnM

__________________

Ric - The Eccentric One
67HR


Senior Member

Status: Offline
Posts: 223
Date:
Permalink  

Bicyclecamper wrote:

Agree PnM

 Ditto



__________________

 

Classified R.E.D. = "Retired & Extremely Disinterested" (Locksmith)
Big Mal


Senior Member

Status: Offline
Posts: 141
Date:
Permalink  

Still not enough room even with the extra backing plate, just how wide is the wall cavity ???? I have removed mine for a refit once and it was a tight fit even for the old style socket and looking at the new version I think I would have dramas as well getting room to fit ........................ Might explain lower placement on outer wall on new vans with a boxed in section inside ..............

Try 2x backing plates or cut out one from HDPE Board, the stuff poly cutting boards are made from, does a great job and is electrical/heat/water insulated and I have used it for a number of things on van especially as backing plate for electrical panel and other panel jobs.... Can get thick cutting boards of the stuff at Bunnings and laminate to get the thickness needed.

 

 The other way would be to cut right thru the inner wall, and cover with a junction box which is what they are for ... a junction box is the stronger of the type..

DETA 108 x 108 x 76mm Adaptable Box PVC | Deta Electrical



-- Edited by Big Mal on Saturday 12th of October 2024 06:10:33 PM

__________________

Checking out the places I drove past a thousand times................

 
Micko69


Member

Status: Offline
Posts: 22
Date:
Permalink  

Thanks everyone for your suggestions, really appreciated. I am certainly not a qualified sparky, was wanting to get the right gear to have a sparky install for me. I may need to put in brackets next time (not a sparky) with future posts - lol. Dont want to upset the electrical police.
Have a good one.

__________________
Micko69


Member

Status: Offline
Posts: 22
Date:
Permalink  

Ah yes, I do care about that, thats why I asked for suggestions before I buy the goods to have a sparky install for me. Where to you get off, giving me a lecture, are you a mind reader?



__________________
Micko69


Member

Status: Offline
Posts: 22
Date:
Permalink  

Geez mate, calm down. I was after some advice. maybe you need to increase the meds! its all good.



__________________
Magnarc


Guru

Status: Offline
Posts: 1279
Date:
Permalink  

Mick. have the electrician purchase and fit it. Why go to all that trouble of finding the right fitting when a qualified person would surely know how to solve the problem????

Unless the pennies are a bit tight?



__________________

Those who wish to reap the blessings of freedom must, as men, endure the fatigue of defending it.

Thomas Paine.

 
KJB


Guru

Status: Offline
Posts: 844
Date:
Permalink  

Good "come back" Mick.......



__________________

KB
jegog


Senior Member

Status: Offline
Posts: 245
Date:
Permalink  

Micko69 wrote:

Ah yes, I do care about that, thats why I asked for suggestions before I buy the goods to have a sparky install for me. Where to you get off, giving me a lecture, are you a mind reader?

 So why did you say in your first post:

" Am having some real problems replacing old 10 and 15 amp with new ones. The new ones dont fit between the out and inner wall. I have bought the largest spacers (20 mm) and they still dont make the outlets fit. "

That tells me that you removed the existing 15A plug and tried replacing it, or do you have Superman's X-ray vision?

 



__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Click here for the Grey Nomads website -> The Grey Nomads Forum -> Techies' Corner -> Old 10amp and 15amp power outlets
Tweet this page Post to Digg Post to Del.icio.us
Purchase Grey Nomad bumper stickers Read our daily column, the Nomad News The Grey Nomad's Guidebook