We have a BT50, and would love to have 2 drawers in the back of the ute (covered in), prices we have been given seem lots dearer that we thought, does anybody have any ideas ???
KFT said
02:40 PM Jan 12, 2014
we have a Navara dual cab and have just had drawers fitted by ARB Tamworth. Also got a drop slide for the 80L waeco.
these bloke did a top quality job and all done for $3250.00
-- Edited by KFT on Sunday 12th of January 2014 03:14:52 PM
wandwill said
03:19 PM Jan 12, 2014
Thank you, will be following all of them up, big differences in prices also, Wandwill
Onedodger said
04:21 PM Jan 12, 2014
Or if you are handy with some tools. Do it Yourself.
I built my own in the rear of my BT50 Dual cab at a total cost of $600 using aluminium and structual plywood.
Not rocket science but a lot of fun in both the planning and building. Plus mucho satisfaction.
Cruising Cruze said
04:50 PM Jan 12, 2014
Have a look at Gumtree seen some there this week you will safe heaps
You can always ask Onedodger to sell his to you would not be $3250.00
Sorry just joking
Cheers John
elliemike said
07:43 PM Jan 12, 2014
If you are reasonably handy with tools have a look at these Youtube Videos on building your own with Aluminum.
I made mine for the Isuzu Dmax they came out just A1. Much better than I expected.
Cost me t $700 all up with carpet as well.
I only made my drawers one metre long, leaving room for storage lockers at the rear of the drawers and also down both sides. The rear storage lockers are for long term spares and stuff not used very often.
Used a cheap drop saw with a good aluminium cutting blade to accurately cut the 1" RHS Ally Tube (it is imperial tube and joiners) Get the RHS square tube from a Aluminium Stock Holder in 6 metre lengths as it is cheaper. I was able to cut all the Ally sheet at my work on the Guillotine. But I would think you could get it all cut for a $100 if you gave the stockholder a cutting list.
If you don't want to DIY then go and see your local sheetmetal worker I had this box with a slide out shelf made including the door and lock for under $300..
Thank you to everyone who has given fantastic suggestions, I am on the road at the moment, but for that amount of saving, will find somewhere to hide up until I have completed the task, again, thank you very much, wandwill
We have a BT50, and would love to have 2 drawers in the back of the ute (covered in), prices we have been given seem lots dearer that we thought, does anybody have any ideas ???
these bloke did a top quality job and all done for $3250.00
If you are looking for a cheaper set up have a look here; www.drifta.com.au/OtherDRIFTAProducts4WD.php
This bloke is reputed to also do a top quality job but for us was too far away.
frank
Here are another couple of solutions that may help solve your problem. the 4WD interiors are the ones fitted by ARB
www.outbacktouringsolutions.com.au/
http://www.4wdinteriors.com/
frank
-- Edited by KFT on Sunday 12th of January 2014 03:14:52 PM
Thank you, will be following all of them up, big differences in prices also, Wandwill
I built my own in the rear of my BT50 Dual cab at a total cost of $600 using aluminium and structual plywood.
Not rocket science but a lot of fun in both the planning and building. Plus mucho satisfaction.
Have a look at Gumtree seen some there this week












you will safe heaps
You can always ask Onedodger to sell his to you
would not be $3250.00
Sorry just joking
Cheers John
If you are reasonably handy with tools have a look at these Youtube Videos on building your own with Aluminum.
I made mine for the Isuzu Dmax they came out just A1. Much better than I expected.
Cost me t $700 all up with carpet as well.
I only made my drawers one metre long, leaving room for storage lockers at the rear of the drawers and also down both sides. The rear storage lockers are for long term spares and stuff not used very often.
Used a cheap drop saw with a good aluminium cutting blade to accurately cut the 1" RHS Ally Tube (it is imperial tube and joiners) Get the RHS square tube from a Aluminium Stock Holder in 6 metre lengths as it is cheaper. I was able to cut all the Ally sheet at my work on the Guillotine. But I would think you could get it all cut for a $100 if you gave the stockholder a cutting list.
Regards
Mike
Four separate parts to this You tube vid.
https://www.youtube.com/watch?v=GaYrMPE9Td0 part 1
https://www.youtube.com/watch?v=8a5Id0mvsGQ part 2
https://www.youtube.com/watch?v=j4UR9fTUUpg part 3
https://www.youtube.com/watch?v=rt7kqgRhgks part 4
If you don't want to DIY then go and see your local sheetmetal worker I had this box with a slide out shelf made including the door and lock for under $300..